Products
Australian Monitor AMD200 Digital Mixer Amplifier
The AMD200 is of 1 RU Class D design, featuring eight balanced Mic/Line level inputs each with 34V DC phantom power available and four dual RCA program source inputs. Delivering 200 watts at 100 volt, 70 volt, 8 ohm or 4 ohm and with on board tones (Bell, Pre Announce, Alert and Evac), remote master VCA, Vox triggered output (assignable to any one or combination of mic/line ins), 24DVC back up power input and low power contact closure.
Description
With an impressive 12 inputs the Australian Monitor AMD200 will give installers untold flexibility in a 1 RU mixer amplifier
Featuring 8 balanced Mic/Line level inputs each with 34V DC phantom power available and 4 dual RCA program source inputs and delivering 200 watts at 100 volt, 70 volt, 8 ohm and 4 ohm. With on board tones (Bell, Pre-Announce, Alert and Evac), remote master VCA, Vox triggered output (assignable to any one or combination of mic/line ins), 24DVC back up power input and low power contact closure, the Australian Monitor AMD200 has all the features of the smaller AMD100 compact class D amplifier.
The AMD200 also boasts the power of on board DSP processing, the connectivity of third party control via the RS485 port, which supports the Australian Monitor ICON CP control panel or allows connection to a third party control system and a USB port for setup or for PC control.
Please note: AMD200 software is only available as a Windows 32Bit application.
Features:
- 8 mic/line inputs + 4 Stereo source inputs
- Stereo line output + Mono amplifier output (Constant voltage or Low impedance operation)
- 1 RU Class D design
- 60 Hz – 20 kHz frequency response amplifier output (20 Hz – 20 kHz Line level output)
- Low power contact closure
- DSP processing on board with Parametric EQ, compressor, delay and high and low pass filters
- Third party control via serial, Software GUI or via Icon-CP control panel
- Remote VCA master volume control
- Mic/Line inputs have 34 volt phantom power
Downloads:
Additional Information
| Frequency response (Mic/Line Inputs) | Line Level Output 20-20kHz, -3dB Signal Input -2dB below clip |
|---|---|
| Frequency response (Stereo Inputs) | Line Level Output 20-20kHz, -3dB Signal Input -2dB below clip |
| Total Harmonic Distortion (Mic/Line Inputs) | Line Level Output <0.05 % 0dB gain Signal Input -2dB below clip |
| Total Harmonic Distortion (Stereo Inputs) | Line Level Output <0.05 % Signal Input -2dB below clip |
| Phantom Power | +34V DC Available via individual switch on each mic/line channel |
| Crosstalk Between channels | > 80dB, 1kHz, input channel at clip, measured on line output of adjacent output |
| Signal To Noise Ratio | Mic/Line Input > 92dB A-weighted, to line and amp output, 20Hz to 20kHz |
| Power Output | 4ohm 200W, 28.28Vrms |
| Power Consumption | Green 9W No control panel attached, 4ohm load |
| Thermal Dissipation | Idle 15W, (51.18BtuHr) Pink noise 12dB crest factor, typical of program music just before clip |
| Power Input | AC Mains (230V to 240V / 115V to 120V) or +24V DC |
| Recommended Operating Temp | 10°C to 45°C (50°F to 113°F) |
| Recommended Operating Humidity | 5% to 95% |
| Dimensions | (H x W x D) 44 x 430 x 330mm (1.75” x 16.9” x 13”) Not including rack ears or front panel knobs |
| Shipping Dimensions | (H x W x D) 140 x 540 x 410mm (5.51” x 21.3” x 16.1”) |
| Weight | Net 7kg (15.4lb) |
Brand
Brand
Australian Monitor
